XScopes User’s Manual Page DS-XScopes-2.2 September, 2012 2. XScopes 2.4.1.3 User’s Manual XY Mode The XY mode changes the display from volts vs. Figure 1: Xprotolab and Xminilab, Top View Figure 2: XScopes Block Diagram. Figure 32: Device mode menus 2.4.1 Oscilloscope Mode This is the default mode of the XScope. C Compiler, included in the WinAVR package: WinAVR at sourceforgeĢ) Can the waveform generator and the oscilloscope run simultaneously?.Integrated Development Environment: Atmel Studio 6.1) What tools do I need to develop my own programs on the XScope?īesides the power supply, you need an external programmer, such as the AVR ISP 2, or a debugger, such as the AVR JTAGICE mkII or the AVR ONE!. In the Mode Menu, press K1 and K3 simultaneously, to display both the Scope and FFT. Contribute to ganzziani/XScopes-Firmware development by creating an account on GitHub. Yes, the waveform generator runs on the background. A node.js driver for Gabotronics Xminilab oscilloscopes Resources. Note: all the action is happening in branch develop for the time being. (The AWG uses the DMA, so it doesn't need any CPU intervention). A node.js driver for Gabotronics Xminilab oscilloscopes. The device can be powered thru the micro USB port. The Xprotolab and Xminilab can be plugged directly on a breadboard. The XScopes can also be used as development boards for the AVR XMEGA microcontroller. Can you find 'ID 16d0:06f9 MCS Gabotronics Xminilab' in lsusb output Is the green LED on the Xprotolab board blinking Top. Do not connect a 5V power supply and the USB at the same time.Ĥ) Can I connect the XScope to the computer to control the oscilloscope and get the data? Alternatively, the device can be powered by connecting a 5V power supply on the 5V pin. The Xprotolab is a fully featured Mixed Signal Oscilloscope (MSO) with Spectrum Analyzer and Arbitrary Waveform Generator (AWG). The XScopes are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator and a protocol sniffer. Old hardware 1.4 and 1.5 cannot do USB firmware upgrades.Ī UART to USB cable is required for hardware 1.4 and 1.5.ĥ) Can I connect the XScope to the computer using the USB for firmware updates? Yes, you can use the XScopes PC Interface. This is the maximum current on each voltage: The XScope can also power external devices. +5V: Will be the same as the power source minus 60mA. Two rows of I/O pin headers are used to bring the Xprotolab I/O pins to the edge of the board. Visualization of the signals and controlling the device can be done through an open-source PC interface software. In addition, this board also adds a 5V switching regulator so that the Xprotolab can be supplied by a 6.3-30V power supply, as well as a Bluetooth module that allows the wireless use of the Gabotronics Xscope computer interface. It’s a nifty little (1 x 2-in.) mixed-signal oscilloscope module blended with a logic analyzer and arbitrary waveform generator. +3.3V: Approximately 200mA, but this subtracts from the available current on the +5V line.ħ) What is the maximum frequency that I can measure with the XScope? 5V: Approximately 50mA, but this subtracts from the available current on the +5V line. The 20 Xprotolab Plain from Gabotronics is one such good option. xscopes-qt_0.0.0-1_armhf.However, you can still measure frequencies up to almost Nyquist/2, i.e. NOTE: you can install Option B: Debian package If you want to run as a non-root user, create a file in /etc/udev/rules.d/les with contents: ACTION="add", SUBSYSTEM="usb", ATTR="Gabotronics", GROUP="dialout", MODE="066", SYMLINK+="XScope%n"Īnd make sure your user is a member of the group specified.Īnd run the program again as a regular user: Product FAQs 1) What tools do I need to develop my own programs on the XScope 2) Can the waveform generator and the oscilloscope run simultaneously 3) How. Test the program by connecting your XMEGA Xprotolab and running the program as root: Sudo apt install git qt5-default libqt5serialport5-dev libusb-1.0-0-dev cmake libudev-dev Clone repositoryĬd xscopes-qt Build Option A: standalone binary Source and binaries are provided, but not for Raspberry Pi.Ĭredit to user nicolewolffer on the Raspberry Pi forum for most of these instructions. The XScopes (Xminilab and Xprotolab) are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator, and a. The Xprotolab XMEGA is a very useful device on it's own but if you want to avoid using the tiny screen/buttons, save waveforms, or modify the Arbitrary Waveform Generator then you want the XScopes PC Interface software. How to compile xscopes-qt from Gabotronics on a Raspberry Pi
0 Comments
Leave a Reply. |